Simrad SP270 Instalační manuál Strana 3
- Strana / 254
- Tabulka s obsahem
- KNIHY
- Installation manual 1
- Simrad SP270 3
- Fishery sonar 3
- Sections 5
- References 6
- The reader 6
- High voltage safety warning 9
- Artificial respiration 10
- Combining ECM and artificial 10
- Do you know what to do? 10
- Introduction 11
- Document revisions 12
- About this document 12
- Table of contents 13
- Blank page 14
- Installation document 15
- Overview 15
- 851-160571 / B 16
- Installation procedures 18
- Auxiliary equipment 19
- Supply conditions 20
- General safety rules 21
- Installation requirements 22
- Dry docking 23
- Equipment handling 24
- Initial preservation 25
- Inspection and unpacking 27
- After use storage 30
- Re-packing 32
- ESD precautions 32
- Temperature protection 33
- Technical specifications 34
- Installation planning 45
- Sonar room requirements 46
- 851-160572 / B 48
- Mounting the trunk 49
- Protecting blister 50
- Corrosion protection 50
- Installation of the hull unit 53
- Alignment of the transducer 54
- Installation checklist 55
- Desk top mounting 61
- Panel mounting 62
- Bulkhead mounting 63
- Cable plan 64
- Sonar Control Unit cabling 66
- Transceiver Unit cabling 67
- Hull Unit cabling 70
- Connecting the course gyro 71
- Connecting the speed log 81
- Connecting a pulse log 81
- S0J 30.06 88
- . . . . . . . . . . . 89
- DQG;ument 90
- PREPARI 91
- Starting 92
- Starting up the Hull Unit 94
- Hand crank 95
- (CD3125) 95
- The motor control unit 95
- STOP position 96
- 380/440V: 2 96
- 380/440V 99
- (CD3127) 99
- Mains connection to the motor 99
- , must then be 100
- Start-up procedures 101
- Middle position switch 101
- 160573/A 101
- Connect the SONAR 102
- , adjust the picture with 103
- ~~'. 104
- Press the CIRCLE 105
- , and press the 105
- TRACK button, (9) and check 106
- Checking the bridge functions 107
- Press the LOWER button for 108
- , and check if the 109
- UPPER is shown in the 110
- (refer to figure 111
- Sonar Control Unit in the 111
- RCG. . . . . 112
- Connecting the transducer 113
- Simrad SP 270 114
- , and check 115
- S8RAD $lIMA!) 116
- J~Gp.rsor to TX 117
- PP FILTER to 118
- ILIARY E 119
- Sonar Control Unit by 120
- , set the speed to 121
- , switch off the 121
- Be aware 122
- , and check that the 123
- Source level 124
- Auxiliary 125
- Ext. trig 125
- 0 Vert. input 125
- Approx. 5 125
- Serial No 126
- , depth and 127
- Measurements/calculations 127
- SL OMNI dB/ /~Pa 128
- Receiving. 129
- Value Unit 130
- Noise/spee 131
- , make the test 132
- ' hull 133
- BEARING WITH 134
- STABLE SPEED 134
- -- - - -- - - 134
- LLAT..IO,Ni; 135
- Installation remarks 135
- Drawings 137
- (;lCUment revisions 138
- Original issue 140
- 851- 160675 / AA000 / 4- 11 147
- Document history 150
- &RQQHFWLQJ WKH 233
- 6LPUDG ,7 233
- 7UDZO ,QVWUXPHQWDWLRQ 6\VWHP 233
- 'RFXPHQW UHYLVLRQV 234
- &RQWHQWV 235
- 'RFXPHQW KLVWRU\ 236
- $ 237
- E 2004 Simrad AS 252
- ISBN 82-8066-014-3 252
Související produkty a manuály pro ne Simrad SP270
(202 stránky)
(44 stránky)
(112 stránky)
(6 stránky)
(25 stránky)
(44 stránky)
(78 stránky)
(79 stránky)
(38 stránky)
(36 stránky)
(25 stránky)
(6 stránky)
(4 stránky)
(1 stránky)
(36 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.038 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce